MTM Trapezium Grinder

MTM Trapezium Grinder

After superfine material, with its surface area increases poly, can cause changes in other properties, and greatly improve the effectiveness and use of materials utilization. Ultra-fine powders and high-tech fields are infiltrated the entire industrial sector, as the origin of the modern high-tech. Ultrafine grinder technology has been widely used in chemical industry, metallurgy, mining, building materials, chemical, food, medicine, agriculture, environmental protection and aerospace and other fields. Service Online >

MTM Trapezium Grinder main characteristics

  • Scope big, can grind against the hardness of various materials in 6 below.
  • Under high pressure spring, the product fineness greatly improved.
  • Compared with the jet mill, low energy consumption.
  • less investment, high efficiency, quick recovery.
  • a system, less production processes, 25mm below the material can be machined directly into.
  • pollution, dust effect fully meet the state standards.
  • good sealing effect roller device.

MTM Trapezium Grinder equipment routine maintenance

  • the transmission part of MTM Trapezium Grinder is mainly used, it must be run under good lubrication conditions, otherwise it will damage the bearings and shorten life.
  • feeding should be uniform, not erratic. Excessive feeding blocked duct will reduce yield, easy to burn out the motor, feeding too little will feed production. Feed size: hard material in less than 15 mm is appropriate when the straight, soft material straight for 20 mm, non-bulk materials added to the machine.
  • non slug into the machine, otherwise it will damage the grinding roller and grinding ring, and even center hanger.
  • fineness adjustment, according to the size of materials, hardness, moisture content, different proportion of different fineness processing, adjustable top analyzer, high speed, fineness, low speed, low fineness. Improve the fineness, the output will be reduced accordingly, if it is below standard debugging fan speed, users can be flexible.
  • the air volume control, the fan intake air flow pipe located on the control valve, generally open to the maximum position, according to the fineness, appropriate adjustments to production requirements. Exhaust outlet valve located on the exhaust pipe, and transferred at the inlet can be no dust ejected. A small amount of wind, fineness. It should be noted, the air volume is too small, easy to precipitate within the host material beneath the duct, make appropriate adjustments.
  • roller MTM Trapezium Grinder scrap ring limit, the remaining minimum wall thickness of not less than 10mm.
  • stop, stop feeding, the host continues , residual abrasive grinding continues, after about a minute, turn off the master motor and the motor analyzer, stop grinding work, which then stops the fan motor, in order to purge the residual powder.

Technical Data

Name MTM100 MTM130 MTM160
Ring roll number(pcs) 4 5 6
Major diameter of roller(mm) Φ310X170 Φ410X210 Φ440X270
Inner diameter of roller(mm) Φ950X170 Φ1280X210 Φ1600X270
Revolving Speed(rmin) 130 103 82
Max feed size(mm) <25 <30 <35
Final size(mm) 1.6-0.045
fineness can reach to 0.038
1.6-0.045
fineness can reach to 0.038
1.6-0.045
fineness can reach to 0.038
Output(th) 3-8 6-11 9-22
Complete physical size(mm) 7100×5900×7900 9200×7250×9700 12550×5700×8355
Main unit motor Model Y225S-4 Y280S-4 Y315M-4
Power(kw) 37 75 132
Rotate speed(rmin) 1480 1480 1480
Centrifugal induced draft fan motor Model Y225S-4 Y280S-4 Y315M-4
Power(kw) 37 75 132
Rotate speed(rmin) 1480 1480 1480
Classifier speed regulating motor Model YCT200-4A YCT200-4B YCT250-4A
Power(kw) 5.5 7.5 18.5
Rotate speed(rmin) 125-1250 125-1250 132-1320
Elevator Elevator model TH210 TH210 TH315
Motor model Y100L2-4 Y100L2-4 Y112M-4
Power(kw) 3 3 4
Rotate speed(rmin) 1430 1430 1440
Jaw Crusher Jaw Crusher Model PE200×350 PE250×400 PE250×750
Main unit motor Y160M-6 Y180L-6 Y200L2-6
Power(kw) 7.5 15 22
Rotate speed(rmin) 970 970 970
Magnetic vibrating feeder Main unit motor GZ2F GZ3F GZ3F
Power(kw) 0.15 0.2 0.2

The latest products

Request a quotation

Simply complete the form below, click submit, you will get the price list and a SBM representative will contact you within one business day. Please also feel free to contact us by email or phone. ( * Denotes a required field).